Item # |
Description |
Price |
Click for more detail...
Hx150
|
Hxtal NYL-1 150 gram kit
Hxtal NYL-1 Epoxy is a crystal clear, non-yellowing, two-part epoxy resin system. Unlike other epoxies that were made for hobbyist, home and industrial uses, Hxtal was designed especially for restoration and conservation. It can be used on glass, porcelain, marble, wood, metal and much more. Hxtal can be colored, or filled to match porcelain.
Hxtal fully cures in approximately 5-7 days at room temperature (75 degrees Fahrenheit). Raising the temperature of the repaired article to 90-100 degrees Fahrenheit for 12 hours or so can cut the cure time to approx. 1-1/2 to 2 days. Raising the temperature of the article being repaired to 130-140 degrees Fahrenheit prior to applying Hxtal will reduce cure time. Raising the temperature of mixed Hxtal to 120-130 degrees Fahrenheit for 15 to 20 minutes prior to use will decrease curing time to as short as 5 to 8 hours. When heating mixed Hxtal, stir the mixture throughout the heating process. Glass rods work well for this. It is best to heat the epoxy slowly and evenly.
Hxtal is most accurately measured by weight, not by volume. Precise measuring is best done using a digital or triple beam scale. Hxtal is mixed by weighing 3 parts of resin to 1 part of catalyst (3:1). Hxtal can be measured using syringes (Monoject Syringes (below) work great for this) though accuracy may not be as precise. Both the resin and catalyst of Hxtal weigh approximately the same, about 2 grams per cc or ml. Thus, you may be able to use Monoject Syringes to measure out appropriate amounts of resin and catalyst.
The unused mix can be kept for 4 to 5 days in the freezer. It is most important that the container be tightly closed.
|
|
 |
Click for more detail...
Hx60
|
Hxtal NYL-1 60 gram Kit
Same as above, only a smaller sized kit.
|
|
|
Click for more detail...
ARAL2020
|
Araldite 2020
This is a low viscosity water clear adhesive especially suited for bonding of glass and ceramics, also for clear castings and laminating. The reflective index is similar to glass. This is an extremely popular product in Europe.
Mixing Ratios:
By Weight: 100:30 Part A:Part B
By Volume: 100:35 Part A:Part B
Total kit size is 500 grams.
|
|
|
Click for more detail...
MonojectSyringe
|
Monoject Syringe
One-piece syringe used for the controlled dispensing of ColdGlaze, epoxy and other resins. The curved tip makes dispensing liquids easier.
Monoject syringe holds 12 ml.
Each pack contains two (2) syringes.
|
|
|
Item # |
Description |
Price |
Click for more detail...
UHUPlusEndfest300
|
UHU Plus Epoxy Adhesive (Endfest 300)
This is a 2-component epoxy adhesive for heavy-duty applications. The bond strength can be increased by curing at a higher temperature. It will set with a very hard surface finish, with high resistance to impact, ageing and moisture.
Materials:
Metals, glass, porcelain, ceramic, wood, marble, stone, concrete, Duroplast®, glass fiber reinforced synthetics, rigid PVC, rubber, rigid foam plastics such as Styropor®. Not suitable for sticking large areas of glass.
Open time:
2 hours at room temperature.
Setting:
The setting time depends on the temperature; final strength can be increased by applying heat (not over 200°C - see table).
Temperature Setting time Strength
20 °C 12 Std. 1200 N/cm2
40 °C 3 Std. 1800 N/cm2
70 °C 45 Min. 2000 N/cm2
100 °C 10 Min. 2500 N/cm2
180 °C 5 Min. 3000 N/cm2
Very popular in Europe.
30 ml pack
|
|
|
Click for more detail...
UHUPlusSofort
|
UHU Plus Sofort Epoxy
2-component adhesive on an epoxy base for particularly quick assemblies over small areas.
Mix Proportion: 1 part binder to 1 part hardener (by volume).
Working time (open time) up to 2 minutes.
Initial strength achieved after 5 minutes.
Final strength = approx. 800 N/cm2.
The adhesive is transparent once it has dried; resists impact, ageing and the effects of moisture.
30 ml pack
|
|
|
Click for more detail...
Epox5
|
Sylmasta Clear Epoxy Adhesive - 5 Minute
This is a fast setting very high strength VERY CLEAR epoxy adhesive. Supplied in a syringe pack for easy and accurate measuring, which reduces wastage.This adhesive can be mixed with micro-fine colours to make any color adhesive to match the item being bonded.
25 ml
|
|
|
